What the Ethernet Cable Voltage Drop Calculator does
The Ethernet Cable Voltage Drop Calculator estimates how much voltage is lost as current travels through a cable run. It uses three values: current in amperes, the resistance of one conductor per meter in ohms per meter, and the one-way run length in meters. The result is labeled Voltage drop (V) and is expressed in volts.
This is a simple resistive estimate for a two-conductor path. Current travels to a device through one conductor and returns through another, so the calculation doubles the one-way length. The tool can help with a first-pass check for low-voltage network equipment, such as a remote access point, camera, or switch powered over a cable. It does not determine whether a particular Ethernet installation or power source is compliant or suitable.
The resistance value should represent one conductor at the conditions relevant to the installation. Cable data sheets may express resistance differently, and resistance can vary with conductor material, gauge, temperature, and manufacturing tolerances. Confirm the meaning and units of the value before using it.
How to use the Ethernet Cable Voltage Drop Calculator
Enter values that describe the circuit being evaluated. Use the same units shown in the fields so the result is interpretable.
- Current (A): Enter the current flowing through the powered circuit in amperes.
- Conductor resistance per meter (Ω/m): Enter the resistance of one conductor for each meter of cable.
- One-way cable run length (m): Enter the physical distance from the power source to the device, in meters.
For example, use 0.5 A, 0.1 Ω/m per conductor, and a 30 m one-way run. The calculation is 2 × 0.5 A × 0.1 Ω/m × 30 m, which gives 3 V of estimated drop. The factor of two accounts for the return conductor. This example illustrates the arithmetic and is not a recommendation for a specific device or cable.
Check that the current and resistance describe the same operating situation. If a device draws a changing current, a single value gives only an estimate for the chosen current. If the manufacturer's cable information gives resistance per pair or for a complete loop, do not treat that figure as per-conductor resistance without converting it appropriately.
How the Ethernet Cable Voltage Drop Calculator formula works
The calculator uses this formula: 2 × current × resistance per meter × run length. It applies the relationship between current, resistance, and voltage drop, while representing both conductors in the circuit.
In unit terms, amperes multiplied by ohms per meter and meters results in volts. The one-way run length is multiplied by two because the circuit includes a path to the load and a return path. The estimate assumes both conductors have the same resistance per meter and that the entered current is the same through the outgoing and return conductors.
The formula does not model connector resistance, splices, parallel conductors, supply regulation, or variations in cable temperature. It also does not calculate the voltage at the device, because that requires the source voltage. To estimate device voltage, subtract the calculated drop from the voltage at the source, using values measured or specified for the same operating conditions.
Keep the units consistent. Entering resistance in ohms per kilometer while labeling it as ohms per meter would produce a result off by a factor of one thousand. Likewise, enter the one-way length in meters rather than the combined length of both conductors, since the formula already applies the factor of two.
Use cases for the Ethernet Cable Voltage Drop Calculator
A voltage-drop estimate can help organize a network cabling assessment before equipment is installed or relocated. Common planning situations include:
- Comparing estimated losses for alternative cable routes of different lengths.
- Checking how a change in expected device current affects the drop.
- Reviewing whether the cable information being used is per conductor or for a pair.
- Preparing questions for an installer or equipment supplier about a long powered run.
- Recording the assumptions behind an initial calculation for later verification.
For a fair comparison, change one input at a time and keep the other two fixed. A longer run increases the estimate in direct proportion to length. The same proportional relationship applies to current and conductor resistance. This makes the calculator useful for understanding sensitivity, but it cannot replace checking the actual cable specification and the equipment's power requirements.
Ethernet describes a data connection, while power delivery can involve additional standards and equipment behavior. If the installation uses Power over Ethernet, confirm the relevant standard, cable category, conductor details, source capability, and device requirements from authoritative product documentation. The arithmetic here only estimates resistive loss based on the supplied inputs.
Other factors to consider when calculating Ethernet cable voltage drop
Before relying on an estimate, verify the resistance figure and the cable path. A route measured on a floor plan may differ from the actual installed length because of vertical sections, service loops, and routing around obstacles. Use the run length that best reflects the conductor path in the installation.
Conductor resistance generally changes with temperature. Cable bundles, warm spaces, and operating conditions can affect the effective resistance. The simple formula does not make a temperature correction, so consult the cable manufacturer's specifications or a qualified network installer when the result needs to represent real operating conditions.
Also consider the behavior of the power source and load. A regulated source may respond to a voltage drop in ways this formula does not represent, and some devices change their current draw as their input voltage changes. The calculated figure is therefore a transparent estimate from fixed inputs, rather than a complete model of the powered network.
Use current and voltage limits from the device and power equipment documentation when evaluating an installation. If a small change in assumptions makes the estimate materially different, verify the values and seek qualified technical review. Keep the calculation, source data, and operating assumptions together so another person can reproduce the result.
Frequently asked questions
Does the calculator use the full cable loop length?
No. Enter the one-way distance from the source to the device. The formula multiplies by two to account for the outgoing and return conductors. Entering the round-trip conductor length and applying the formula would count that path twice.
What resistance value should I enter?
Use resistance per meter for one conductor, in ohms per meter. Check the cable documentation carefully, because values may instead describe a pair, a loop, or a different length unit. Convert the specification before entering it if its basis differs.
Can this estimate be used for every Ethernet cable?
It can perform the stated arithmetic for any supplied inputs, but the result is only meaningful when the resistance and current represent the cable and operating condition. Cable construction, temperature, connectors, and power equipment can affect a real installation.
Does voltage drop tell me the voltage received by the device?
No. The result is the estimated difference between source and load voltage across the modeled conductors. To estimate the device-side voltage, subtract the drop from the source voltage measured or specified under matching conditions.
Does this calculator confirm that a Power over Ethernet run is safe?
No. It does not assess standards compliance, cable heating, equipment compatibility, or installation quality. Use product documentation and applicable requirements, and obtain qualified technical review when needed.